How to fix the BIOS error

SOLUTIONS

THE DETAILED SOLUTION FOR ERROR

FIX THE 0X0000007B ERROR

solution for  0X0000007B error 

1.  Restart your computer

2.Verify that the hard disk is properly installed or not

3.Start using Last Known Good Configurations

4. Undo any changes made to the hard drive

5.Change your SATA Operation

6.Run chkdsk on your hard drive

7.Repair windows using Windows installation media in USB drive

8.Reinstall Windows system to fix 0x0000007B error

1. RESTART THE COMPUTER

A basic reboot can fix numerous computer problems. The 0x0000007B error might have occurred when your computer does not launch correctly. Reboot your computer often might fix your issue. After rebooting, check to see if it still shows the blue screen.

2. VERIFY THAT THE HARD DISK IS PROPERLY INSTALLED OR NOT

Verify that the hard disk is correctly installed. An improperly installed hard disk might cause 0x0000007B errors and other concerns. Check all the wires are properly connected to both hard disk and the motherboard. Try to disconnect the wires and reconnect them.

3. START USING LAST KNOWN GOOD CONFIGURATIONS

If you just recently made some new configurations on your drivers or computer in general, then you can Start-up your computer with Last Known Good Configurations option by clicking F8 Key. If your computer start-up and the 0x0000007B error stop appearing, then the fault it’s on the configurations you made.

4. UNDO ANY CHANGES MADE TO THE HARD DRIVE

Did you just install or make a change to a hard disk controller? If so, there’s a great chance that the change you made triggered the STOP 0x0000007B error.

            • Undo the change and test for the 0x0000007B blue screen error.
            • Depending on what changes you made, some solutions might include:
            • Removing or reconfiguring the newly installed hard drive controller.

5. CHANGE YOUR SATA OPERATION

In some cases, 0x0000007B stop error could be due to the boot sectors issue. Try to alter your SATA Operation to resolve your issue:

1) Restart your computer and press F2 continuously.

2) Your computer should then boot into the Bios. Then press the arrow key to select SATA Operation > ATA.

                   

3) Press the Enter key on your keyboard. 4) Click Yes when asked to if save changes.

5) Press F10 continuously on your keyboard till the following window pops up; then click Yes.

6) Press the Enter key and wait your computer to boot into Windows.

7) Check to see if your Windows still shows the blue screen.

6. RUN CHKDSK ON YOUR HARD DRIVE

A useful command you can use is the chkdsk. If the data on your hard drive is damaged, then with this command you may repair them. The procedure:

1.Open the terminal of Windows (write “command prompt” in the search box)

2. In the black box that will appear to type the command: “chkdsk c: /r”

3. computer will start running this command on your terminal. When it’s done, you can restart your computer to check if the STOP 0x0000007B ERROR is fixed. If not, then keep trying other methods from this article.

7.REPAIR WINDOWS USING WINDOWS INSTALLATION MEDIA IN USB DRIVE

Set USB as a Windows installation drive in advance and connect it with PC. Restart PC and press F12 constantly till Boot Windows menu appears. Select USB as boot drive to try to reboot Windows. If it fails, reboot PC and press F2 to enter BIOS. Set SATA Mode from AHCI to IDE and then Save changes and reboot. Choose to load Windows from USB flash drive and you’ll enter a Windows Setup window with below choice:

1.To set up Windows now, press ENTER;

2.To repair Windows installation using Recovery Console, press R;

3.To quit Setup without installing Windows, press F3.

8. REINSTALL WINDOWS SYSTEM

The last option left is a fresh windows installation. If none of the above methods work for you, then only you should opt for this method. Go to Microsoft website and download a Windows 7 system image for your PC. You can install the image in your USB drive or burn a windows CD and connect it with PC.

To boot with the USB drive press Del and enter BIOS and set USB as the boot media, and if you are installing with a CD select DVD Drive as 1st bootable device.

INVALID_DATA_ACCESS_TRAP (Error Code 0x00000004)

This is one of the several BSOD errors we have. It can occur in the latest Windows 10 to XP.

  • it can happen when you install new hardware or driver
  • delete registry entries to remove the Error 0x00000004
  • Update all your PC drivers
  • RAM cleaning

FIX THE ERROR CODE 0x00000004

The following troubleshooting steps can be tried to get out of this error code INVALID_DATA_ACCESS_TRAP.

  • You can use software like Cleaner and delete registry entries to remove the Error 0x00000004. This will then remove this error.
  • Use prominent anti-virus like Bit-defender, McAfee, and anti-malware like Malware-bytes to remove any infection on your computer.
  • Update all your PC drivers, including the system drivers like.Net package, etc.
  • Uninstall any new software and reinstall it and update the drivers for it, if necessary.
  • Check hardware corruption using the command chkdsk/ or any other interface tool.
  • Remove the RAM from the slot and clean the golden edges with a dry clean cloth and reinsert it and see.

NTFS_FILE_SYSTEM (Error Code 0x00000024)​

This BSOD error can cause the system to crash suddenly after a stop error. It becomes difficult even to note down the error code. The main reason is that it is a bug check value error code problem.

It indicates a possible disk file-system corruption and most likely caused by failing sectors of your hard-disk. This is related to the NTFS file system. To further not kill your PC, the automatic mechanism shutdowns your computer.

The problem occurs in the NTFS.SYS file. This is a driver file that allows the PC to read and write from the NTFS file system. Even if you have FAT32 or FAT16 systems, you can get a read error

This BSOD error can cause the system to crash suddenly after a stop error. It becomes difficult even to note down the error code. The main reason is that it is a bug check value error code problem.

The problem occurs in the NTFS.SYS file. This is a driver file that allows the PC to read and write from the NTFS file system. Even if you have FAT32 or FAT16 systems, you can get a read error

          • You can use Windows Defender and Security Essentials to recheck your PC for virus/malware and clean them.
          • Check hard disk corruption using the command CHKDSK /F command mentioned earlier, answering the prompt messages.
          • Check for outdated drivers using any Driver Updater tool. These tools check all the drivers on your PC and automatically update them to the latest ones.
          • Run a disk fragmentation tool available inside Windows. You can also try repairing individual slots on your Hard Disk using the software.

NMI_HARDWARE_FAILURE (Error Code 0x00000080)​

NMI_HARDWARE_FAILURE(Error Code 0x00000080)

This type of error code can crop up while playing a game, and the system suddenly crashes.

You can send the dump files to an MVP expert or post in Microsoft forums.

The main two reasons for this kind of error are –

  1. Driver error
  2. Memory error

So first, you need to check whether all your drivers are updated if you were using the latest version of Windows 10. If that doesn’t work out, you can try the generic drivers given by Windows 10 itself.

Generally, by now, manufacturers would have provided the latest drivers. But if it’s an old PC, you may have trouble finding it. Then you can Google for the particular driver file and see if it fits in.

If that doesn’t work out, you need to do a Memory test. This, like checking whether your hard disk or RAM are working properly are not.

            • You can use “Just stress testing” option.
            • Then use the “Blend” test.
            • The number of torture test threads should be equal to the number of CPU cores.
            • Run the test for 6 to 24 hours or until you get errors.

Then you get a log of what hardware is killing your PC

 

DATA_BUS_ERROR (Error Code 0x000000e2)

DATA_BUS_ERROR (Error Code 0x000000e2)

  • corrupted hardware
  • Compatibility problem of hardware devices and OS.
  • BAD RAM
  • L2, L3, etc. kind memory cache errors
  • flash drive, SSD, USB card kind of errors
  • faulty configuration

1. REMOVE NEWLY INSTALLED HARDWARE

The first step you should take is to remove any newly installed hardware from your computer. If you’ve just put some new components into your system, it’s likely the case that these new pieces of hardware will continually be conflicting with your system and therefore causing a large number of errors. To fix this, it’s advisable to remove any of the new pieces of hardware you’ve added, even if you have just put a USB drive onto your system!

2. Ensure That All The Cables Of Your PC Are Working Correctly

The cables of your computer are essential to help your system to read all the important components your entire system requires to run. If you’re experiencing hardware problems (which is one of the main causes of the 0x0000002E error), it could because you have some sort of issue with the cables of your PC. In order to resolve the issue you’re seeing, you need to be able to ensure that all the cables are secured in the rear of your system – allowing your PC to run much smoother again as a result.

3. Ensure All The Drivers For Your PC Are Working Correctly

The “drivers” of your computer are the pieces of software used by your system to help your system to correctly integrate its software with its hardware – allowing your system to run much smoother and more reliably as a result. If you’re seeing problems caused by the hardware of your PC, it’s likely that the drivers of your system are either outdated or not working correctly. To fix this problem, you should look to use the steps outlined here:

  • Click “Start > Control Panel > Device Manager
  • Look through the list of drivers of your computer
  • If you see any yellow icons by the devices, right-click & uninstall the driver
  • Restart your PC and allow the driver to re-install

This will basically allow your computer to read all the files that it needs to run your hardware properly, preventing the 0x0000002E error to appear on your system again. This will ensure that your computer is able to run smoothly, but may not resolve the error you’re seeing.

4. Clean Out The Registry

The “registry” is a very important part of your system which stores all the settings & options of your computer inside. The registry database is one of the most vital parts of all Windows computers, and is responsible for saving everything from your desktop wallpaper to your most recent emails. Despite working normally on most computers, the registry is continually causing a huge number of problems for your system. To fix this problem, you need to be able to cure any of the issues you’re seeing by using a registry cleaner application to scan through your computer and repair any of the problems that your system may have inside. This should resolve the 0x0000002E error on your computer if the above steps failed.

Add a Comment

Your email address will not be published. Required fields are marked *

Translate »